Steel products: six material families
Stainless steel, copper, aluminium, carbon steel, galvanized steel and alloy steel — supplied as plate and sheet, coil and strip, pipe and tube, bar and rod, and profile. Grades, equivalents and specification summaries for each family are below.
Stainless steel
Stainless steel is a chromium-alloyed steel with a passive surface layer that resists corrosion in acids, alkaline gases and solutions. It is not rust-free in every environment, which is why grade selection matters: 304 covers general indoor and food-contact work, 316L adds molybdenum for chlorides, 321 and 310S take heat, and 904L handles aggressive chemical service.
- 304 / 304L
- 316 / 316L
- 321
- 310S
- 347
- 904L
- 301 / 302 / 305
Forms available: Plate / sheet · Coil / strip · Pipe / tube · Bar / rod · Profile
304 / 304L
304 (UNS S30400, EN 1.4301) is the most widely used austenitic stainless steel: 18% chromium, 8% nickel, non-magnetic in the annealed condition and suitable for food-contact, architectural and general fabrication.
View specifications
316L
316L (UNS S31603, EN 1.4404) adds 2–3% molybdenum to the 18/8 base, raising resistance to pitting and crevice corrosion in chlorides.
View specifications
321
321 (UNS S32100, EN 1.4541) is a titanium-stabilised austenitic grade that resists intergranular corrosion after welding and performs in continuous service up to about 870 °C.
View specificationsStainless steel: full range
Grade equivalents, forms, finishes, tolerances and FAQ for this family.
Open family pageCopper
Copper is specified where electrical and thermal conductivity matter more than strength: heat exchangers, refrigeration circuits, busbars, roofing and architectural work. Oxygen-free and phosphorus-deoxidised grades behave differently under brazing and welding, so the temper and grade are quoted together with the form.
- C11000 (ETP)
- C12200 (DHP)
- C12000 (DLP)
- C70600 (90/10 Cu-Ni)
Forms available: Tube / pipe · Plate / sheet · Strip / coil · Bar
C12200
Refrigeration and air-conditioning copper tube made to DIN 8905 and EN 12735 T1/T2 from 99.9% copper, blank inside, clean and dry — supplied in pancake coils and straight lengths in soft, half-hard and hard temper..
View specificationsCopper: full range
Grade equivalents, forms, finishes, tolerances and FAQ for this family.
Open family pageAluminium
Aluminium is chosen for its strength-to-weight ratio and its natural oxide layer. The alloy series decides the rest: 1xxx is commercially pure and highly conductive, 3xxx is a general-purpose manganese alloy, 5xxx is marine-grade magnesium alloy, and 6xxx is heat-treatable structural extrusion stock.
- 1050 / 1060
- 1100
- 3003
- 5052
- 6061
- 6063
Forms available: Plate / sheet · Coil · Pipe / tube · Bar / profile
5052
5052 is the highest-strength common non-heat-treatable aluminium alloy, with excellent fatigue strength and good resistance to salt water and industrial atmospheres.
View specificationsAluminium: full range
Grade equivalents, forms, finishes, tolerances and FAQ for this family.
Open family pageCarbon steel
Carbon steel is the default structural and fabrication material: predictable welding behaviour, wide availability and the lowest cost per tonne of the families on this site. The grade controls strength and weldability, so structural work usually specifies A36, SS400, S235JR or Q235B, while pressure and machinery parts move to Q345B, S355JR or a dedicated pipe grade.
- Q235B
- Q345B
- SS400
- A36
- 20# / 45#
Forms available: Plate / sheet · Coil / strip · Pipe / tube
Galvanized steel
Galvanized steel is carbon steel protected by a hot-dip zinc layer that sacrifices itself before the base metal corrodes. Coating mass — expressed as Z120, Z275 and similar designations — decides service life far more than sheet thickness, so the coating specification belongs next to the grade on every inquiry.
- DX51D+Z
- SGCC
- S350GD+Z
- Z120 / Z275 coating
Forms available: Plate / sheet · Coil / strip · Pipe / tube
DX51D+Z
DX51D+Z is the standard forming and bending grade of hot-dip galvanized steel to EN 10346, supplied with regular spangle or skin-passed surface and zinc coatings from Z120 to Z275 for roofing, ducting and general fabrication..
View specificationsGalvanized steel: full range
Grade equivalents, forms, finishes, tolerances and FAQ for this family.
Open family pageAlloy steel
Alloy steel adds chromium, molybdenum, manganese or nickel to carbon steel to raise hardenability, strength at temperature or wear resistance. The trade-off is heat treatment: 4140 needs quench and temper to reach its properties, 15CrMo and 12Cr1MoV are specified for pressure parts at temperature, and 20CrMnTi is a case-hardening gear steel.
- 42CrMo / 4140
- 40Cr
- 20CrMnTi
- 15CrMo
- 12Cr1MoV
- 65Mn
Forms available: Plate / sheet · Bar / rod · Pipe / tube
4140 / 42CrMo
4140 (42CrMo, EN 1.7225) is a chromium-molybdenum alloy steel with high hardenability and good fatigue resistance, used for shafts, gears, connecting rods and mould bases.
View specificationsAlloy steel: full range
Grade equivalents, forms, finishes, tolerances and FAQ for this family.
Open family pageCan't find your grade?
Non-standard grades, sizes and tempers are quoted against your drawing or standard reference.