Why the finish matters

Stainless steel resists corrosion because of a passive chromium oxide layer, and that layer forms in air regardless of how the surface was produced. Finish matters for three other reasons: appearance, cleanability and cost.

A smoother surface holds less soil and cleaning residue, which is why hygienic equipment specifies BA or polished surfaces rather than 2B. A rougher surface hides scratches and handling marks better, which is why No.4 is used on lift panels and kitchen equipment. And each additional processing step adds cost, so a finish specified out of habit rather than function is money spent for nothing.

Mill finishes: No.1 and 2B

No.1 is hot rolled, annealed and descaled. It has a dull, slightly rough grey surface and is the standard finish for plate that will be further processed, or for industrial applications where appearance is irrelevant. Thickness above roughly 3 mm is normally supplied No.1.

2B is cold rolled, annealed and pickled, then skin-passed between polished rolls. The result is a smooth, slightly reflective grey surface with a fine, non-directional appearance. It is the most common finish in the trade and the correct default for parts that will be formed, welded and then either painted, hidden or used as-is.

2B is also the substrate for most polished finishes. When a buyer asks for No.4 on 1.5 mm sheet, the mill route is usually 2B plus a polishing pass.

BA: bright annealed

BA is cold rolled and annealed in a controlled atmosphere that prevents oxidation, so no pickling is needed and the surface stays bright. Visually it is more reflective than 2B, with a slightly bluish lustre, and it is smoother at the micro scale.

BA is specified where appearance and cleanability matter but a mechanical polish is not required: appliance panels, catering equipment, sterilisation trays, pharmaceutical equipment. It is not a mirror finish, and it will not hide surface defects — BA is unforgiving of scratches and handling marks, so protective film is normally applied.

Polished: No.4, HL and 8K

No.4 is a mechanical polish with a coarse abrasive belt, typically around 120–150 grit, producing a uniform brushed appearance with visible but short grain. It is the standard architectural finish, used on kitchen equipment, lift interiors and cladding where a consistent satin look is wanted.

Hairline (HL) is a finer, longer, continuous brushed pattern, produced with a finer abrasive and a controlled direction of travel. It reads as a series of fine lines rather than a uniform satin, and it is specified for lift panels and fascias where the grain direction is part of the design.

8K is a mirror polish, produced in successive steps up to a very fine abrasive and buffing compound. It reflects images without visible grain, which is why flatness becomes critical: on a thin sheet, a mirror finish shows every wave in the substrate.

Polished finishes are directional. Two adjacent panels polished in different directions will not match under raking light, even if both are correctly made, so the grain direction should be specified on the order and maintained during installation.

Comparison table

Table 1 — Common stainless steel finishes and their typical use
FinishProcessAppearanceTypical use
No.1Hot rolled, annealed, descaledDull grey, roughIndustrial plate, further processing
2BCold rolled, annealed, pickled, skin-passedSmooth, slightly reflectiveGeneral fabrication, forming, welding
BACold rolled, bright annealedBright, reflective, no grainAppliances, catering, pharmaceutical
No.4Mechanical polish, coarse beltUniform satin, short grainArchitecture, kitchen equipment
HLMechanical polish, fine, directionalFine continuous linesLift panels, fascias, cladding
8KMirror polish and buffMirror, no visible grainDecorative panels, reflectors

How to specify a finish

Name the finish by its standard designation and add the practical conditions that the designation does not cover:

  • Standard and designation, for example "2B to EN 10088-2" or "No.4 polished both sides".
  • Which side is finished, where it matters: one side polished is common, both sides polished costs more.
  • Grain direction for HL and No.4, relative to the sheet length.
  • Protective film, and whether it must be laser-safe or UV-resistant if the sheet will be cut or stored outdoors.
  • Roughness where cleanability is regulated, expressed as an Ra value measured to a stated standard.

Finish is also the specification most likely to be the subject of a claim, because "brushed" and "mirror" mean different things to different people. Writing the designation and the roughness value into the order removes most of that ambiguity before the goods are made.